Guide · Homeowners · 4 min read · Updated 17 November 2026
How to Fix Creaking Stairs: Causes and Proper Repairs
Short answer
Stairs creak when treads, risers and strings rub as they flex, usually because wedges have shrunk, glue blocks have failed or nails have loosened. The best repair is from underneath: re-gluing and re-driving wedges and adding glue blocks. If the underside is closed, treads are screwed down into the risers from above. A full flight typically costs £120–£280.
Why stairs creak
A traditional timber staircase is built from treads, the parts you step on, and risers, the vertical boards between them, fixed into two side boards called strings. On most closed-string stairs, each tread and riser sits in a groove routed into the strings and is locked in place with glued timber wedges driven in from underneath. Small triangular glue blocks are fixed along the joint between the tread and riser to stop them moving against each other.
Over time, timber dries and shrinks, glue fails, wedges loosen and nails work free. When you step on the tread, it moves slightly, rubbing against the riser, a wedge or a nail, and that friction is the creak. Central heating, which dries timber, often makes creaks worse in winter.
- Shrunken or loose wedges in the string housings
- Glue blocks that have fallen off or failed
- Nails that rub as the tread flexes
- Gaps between tread and riser
- Movement where the stair meets the floor or landing
The best fix: working from underneath
If you can reach the underside of the stair, for example from an under-stairs cupboard with no plasterboard ceiling, the joiner can repair the stair properly without touching the treads. Loose wedges are knocked out, cleaned, glued and driven back in tightly, or replaced with new ones. New glue blocks are glued and pinned or screwed into the angle between each tread and riser. Where the tread and riser have separated, screws through the bottom of the riser into the back of the tread below draw them together.
This fixes the cause of the movement rather than masking it, and because nothing is visible from above, there is no need to lift carpet or fill holes. It is the method most joiners prefer.
Fixing from above
When the underside is plastered or boarded over, the repair is done from above. The joiner finds the creak by having someone step on each tread, then drives screws down through the front of the tread into the top of the riser below, drawing the tread down tight. Screws are countersunk and the holes filled. On bare timber stairs, the filler is coloured to match or plugs of matching timber are glued in. On carpeted stairs, the carpet is lifted along the nosing and refitted afterwards.
Some creaks come from the back of the tread, where it meets the riser above. A thin bead of adhesive or a small screw at the back edge can stop that movement. Lubricating powders can quieten a creak temporarily, but do not fix the cause.
| Method | When it is used | Visible afterwards? |
|---|---|---|
| Re-glue and re-drive wedges | Underside accessible | No |
| Add glue blocks | Underside accessible | No |
| Screw riser into tread from below | Underside accessible | No |
| Screw tread into riser from above | Underside closed | Filled holes or plugs |
| Lubricating powder | Temporary quick fix | No, but creak returns |
When a creak means something more serious
Most creaks are harmless, but some are signs of a bigger problem. A tread that visibly flexes or bounces may be split along its length. A tread that has dropped at one end may have come out of its housing in the string. A stair that has pulled away from the wall, or where the strings show cracks, needs a closer look. In older houses, woodworm or rot in timbers near damp walls can weaken a stair.
If you notice any of these, a joiner should inspect the stair. A split tread can be replaced, typically for £150–£350, but structural problems with strings or the stair's fixings to the floor and landing need a fuller assessment.
Creaks in landings and winders
Not every noise comes from a straight tread. Landings are built like small floors, with boards on joists, and creak for the same reasons as floorboards: boards rubbing on each other or on nails as the joists flex. Screwing boards down into the joists, using screws long enough to bite properly and avoiding pipes and cables below, usually solves this. Winder treads at a turn are supported differently, often on bearers fixed to the wall and to a newel post, and creaks there can come from a loose bearer or a newel that has moved.
Where the stair meets the ground floor or the landing trimmer, the joint can open up as the house settles or the timber shrinks. A joiner can pack and refix these joints. Taking time to find exactly where the noise comes from, by listening carefully while someone steps slowly on each part, is the key to a lasting repair.
- Landing boards: screw into joists, avoiding services
- Winders: check bearers and newel fixings
- Top and bottom joints: pack and refix
DIY or call a joiner?
Adding glue blocks and screws from underneath is a manageable DIY job if you have good access and basic tools. Screwing down from above on a bare timber stair needs more care to avoid splitting the tread and to get a neat finish. On carpeted stairs, lifting and refitting carpet neatly is a skill in itself, and gripper rods and tacks are easy to damage. A joiner will usually silence a full flight in a few hours and can check for split treads and loose spindles at the same time. We arrange creaking stair repairs through vetted local joiners.
Questions people also ask
Can creaking stairs be fixed without removing the carpet?
Often, yes. If the underside is accessible, the joiner can re-glue wedges and add glue blocks without touching the carpet. From above, special screw kits allow screwing through carpet and snapping off the screw head below the pile, though lifting the carpet along the nosing gives a more reliable result.
Are creaking stairs dangerous?
Usually not. Most creaks are just friction between loose parts. But a tread that bounces, has split or has dropped at one end can be a sign of structural damage and should be checked. Fixing creaks early also stops small movements from becoming bigger problems.
Why are my stairs creaking more in winter?
Central heating dries the air and the timber, which shrinks slightly and opens up joints, so wedges and glue blocks loosen. In summer, higher humidity can swell the timber and quieten creaks. A proper repair with glue and screws keeps the parts tight year round.
Written and checked by the Step Repair team. Read our editorial policy.
More guides
How Much Does Step Repair Cost in the UK?
Fixing a creaking staircase typically costs £120–£280 for a full flight, and replacing a broken stair tread £150–£350. Outside, concrete step edge…
Concrete Step Repair: Fixing Cracked, Chipped and Crumbling Steps
Chipped or crumbling concrete step edges are repaired by cutting back to sound concrete and rebuilding the nosing with a polymer-modified repair…
Stone Step Repair and Resetting: A Guide for Older Homes
Loose stone steps are repaired by lifting the treads, cleaning off failed mortar and rebedding them level, usually on lime mortar in older…
Who Is Responsible for Repairing Steps? Landlords and Owners
In rented homes in England, landlords are usually responsible for repairing the structure and exterior, which can include front steps, under section…
Get a free step repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote