Step Repair

Guide · Homeowners · 4 min read · Updated 17 November 2026

Concrete Step Repair: Fixing Cracked, Chipped and Crumbling Steps

Short answer

Chipped or crumbling concrete step edges are repaired by cutting back to sound concrete and rebuilding the nosing with a polymer-modified repair mortar, typically £150–£400 for one to three steps. Steps that are cracked through, rocking or sitting on a failed base are broken out and recast with new shuttering, from £350 per step. Curing time is needed before full use.

Concrete Step Repair: Fixing Cracked, Chipped and Crumbling Steps

Why concrete steps fail

Concrete steps take a lot of punishment. The front edges, or nosings, get knocked by bins, wheelbarrows and shoes, and their thin section makes them the first part to chip. Water soaks into cracks and small holes, freezes in winter and expands, prising off flakes of concrete in a process called spalling. De-icing salt speeds this up. Where steps were cast without a proper base, or the ground beneath has washed out or settled, the whole step can crack or rock.

In older concrete, the steel reinforcement, if there is any, can rust when water reaches it, expanding and pushing off the concrete above. Rust stains or exposed bars are a sign that a simple surface repair will not be enough.

  • Impact damage to front edges
  • Freeze-thaw spalling, made worse by salt
  • Settlement or wash-out of the base
  • Rusting reinforcement in older concrete
  • Poor original mix or thin sections

Repairing chipped edges and surface damage

For chipped nosings and surface spalling, the repair starts with cutting back all loose and weak concrete until sound material is reached. Edges are cut square rather than feathered, because thin edges of repair mortar break off easily. The area is cleaned and dampened or primed according to the repair product. Timber shuttering is fixed to the face of the step to form a new crisp edge, and a polymer-modified or rapid-setting repair mortar is packed in, compacted and trowelled to match the tread.

The shuttering is removed once the mortar has set, and the surface is finished to give grip. A slightly textured or brushed finish is safer than a smooth trowelled finish on outside steps. Colour matching new mortar to weathered concrete is rarely perfect at first, but it tones in over time.

Recasting a failed step

When a step is cracked through, rocking or crumbling deep into its body, repairs will not last. The failed step is broken out, the base is checked and, if needed, dug out and replaced with compacted sub-base. Timber shuttering is set to the correct rise and going, matching the steps above and below, and reinforcement mesh may be added. Concrete is placed, compacted to remove air pockets and finished with a non-slip texture. The shuttering stays in place until the concrete has gained enough strength.

Getting the rise right matters. Approved Document K expects consistent rises within a flight for new and replacement stairs, and an odd-height step among others is a classic trip hazard.

ProblemTypical repairTypical price
Chipped nosings on one to three stepsCut back and rebuild with repair mortar£150–£400
Surface spallingCut back, prime and resurfaceOften within £150–£400 for a small area
Step cracked through or rockingBreak out and recastfrom £350
Whole flight failingRebuild on a new basePriced after survey

Curing and aftercare

New concrete and repair mortar need time to cure. Concrete gains strength over days and weeks, and needs protecting from rapid drying in hot weather and from frost in cold weather. Many tradespeople cover new work with damp hessian or plastic in warm conditions and avoid casting when frost is forecast. Rapid-setting repair mortars can allow light use sooner, but always follow the product instructions.

Afterwards, avoid using rock salt on new concrete in its first winter where possible, as salt accelerates spalling. Clearing standing water, fixing leaking gutters that drip onto steps and keeping the surface free of moss all extend the life of concrete steps.

Adding handrails and improving safety

A repair is a good moment to make steps safer overall. A sturdy handrail beside external steps helps everyone, particularly older visitors and anyone carrying shopping, and is often simple to add with posts set in concrete or brackets fixed to an adjacent wall. Contrasting nosing strips or a painted edge help people with poor eyesight see where each step begins. Outdoor lighting, even a single motion-sensor light, makes steps much safer after dark.

If the steps are part of the route into a home for someone with reduced mobility, it may be worth considering whether a ramp, an extra handrail or a change to the step heights would help. Consistent rises and reasonably deep goings are easier and safer for everyone to use.

Drainage around the steps is worth checking too. If water runs across the steps from a path, lawn or downpipe, redirecting it with a channel, gully or adjusted fall helps keep the treads dry, reduces moss growth and protects the new repair from frost damage.

  • Fit a sturdy handrail beside external steps
  • Mark nosings with a contrasting edge
  • Add outdoor lighting for evening use
  • Redirect water away from the treads

DIY or professional?

Small chip repairs with a bagged repair mortar are possible for a confident DIYer, but the common failures are feathered edges that break off, poor bond because the surface was not prepared, and rough or slippery finishes. Recasting steps involves breaking out concrete, preparing a base, accurate shuttering and placing concrete correctly, and is usually best left to a groundworker or bricklayer. We arrange concrete step repairs through vetted, insured local trades who will assess whether a repair or recast is the right answer.

Questions people also ask

Can you repair a crumbling concrete step?

Yes, if the damage is on the surface or the edges. Loose concrete is cut back to sound material, and the step is rebuilt with a repair mortar and shuttering. If the crumbling goes deep into the step, or it rocks, recasting on a sound base is the more lasting answer.

Why do concrete steps crack?

Common causes are frost getting into small cracks, settlement or wash-out of the ground underneath, impact on thin edges, rusting reinforcement and poor original construction. Identifying the cause matters, because a surface repair will not last if the base underneath is still moving.

How do I make concrete steps less slippery?

A brushed or textured finish on repaired or recast steps gives better grip than a smooth one. Existing steps can be treated with anti-slip coatings or fitted with anti-slip nosings. Keeping steps clear of moss, algae and standing water also makes a big difference.

Written and checked by the Step Repair team. Read our editorial policy.

Get a free step repair quote

Tell us what you need and we'll come back with a clear price.

Request a quote